console.conf

;
; Configuration for chan_console, a cross-platform console channel driver.
;

[general]

; Set this option to "yes" to enable automatically answering calls on the
; console.  This is very useful if the console is used as an intercom.
; The default value is "no".
;
;autoanswer = no

; Set the default context to use for outgoing calls.  This can be overridden by
; dialing some extension@context, unless the overridecontext option is enabled.
; The default is "default".
;
;context = default

; Set the default extension to use for outgoing calls.  The default is "s".
;
;extension = s

; Set the default CallerID for created channels.
;
;callerid = MyName Here <(256) 428-6000>

; Set the default language for created channels.
;
;language = en

; If you set overridecontext to 'yes', then the whole dial string
; will be interpreted as an extension, which is extremely useful
; to dial SIP, IAX and other extensions which use the '@' character.
; The default is "no".
;
;overridecontext = no    ; if 'no', the last @ will start the context
                        ; if 'yes' the whole string is an extension.


; Default Music on Hold class to use when this channel is placed on hold in
; the case that the music class is not set on the channel with
; Set(CHANNEL(musicclass)=whatever) in the dialplan and the peer channel
; putting this one on hold did not suggest a class to use.
;
;mohinterpret=default

;------------------------------ JITTER BUFFER CONFIGURATION --------------------------
; jbenable = yes              ; Enables the use of a jitterbuffer on the receiving side of an
                              ; Console channel. Defaults to "no". An enabled jitterbuffer will
                              ; be used only if the sending side can create and the receiving
                              ; side can not accept jitter. The Console channel can't accept jitter,
                              ; thus an enabled jitterbuffer on the receive Console side will always
                              ; be used if the sending side can create jitter.

; jbmaxsize = 200             ; Max length of the jitterbuffer in milliseconds.

; jbresyncthreshold = 1000    ; Jump in the frame timestamps over which the jitterbuffer is
                              ; resynchronized. Useful to improve the quality of the voice, with
                              ; big jumps in/broken timestamps, usually sent from exotic devices
                              ; and programs. Defaults to 1000.

; jbimpl = fixed              ; Jitterbuffer implementation, used on the receiving side of a Console
                              ; channel. Two implementations are currently available - "fixed"
                              ; (with size always equals to jbmax-size) and "adaptive" (with
                              ; variable size, actually the new jb of IAX2). Defaults to fixed.

; jbtargetextra = 40          ; This option only affects the jb when 'jbimpl = adaptive' is set.
                              ; The option represents the number of milliseconds by which the new
                              ; jitter buffer will pad its size. the default is 40, so without
                              ; modification, the new jitter buffer will set its size to the jitter
                              ; value plus 40 milliseconds. increasing this value may help if your
                              ; network normally has low jitter, but occasionally has spikes.

; jblog = no                  ; Enables jitterbuffer frame logging. Defaults to "no".
;-----------------------------------------------------------------------------------


;
; Any configuration context defined beyond the [general] section configures
; specific devices for use.
;

[default]
input_device = default       ; When configuring an input device and output device,
output_device = default      ; use the name that you see when you run the "console
                             ; list available" CLI command.  If you say "default", the
                             ; system default input and output devices will be used.
autoanswer = no
context = default
extension = s
callerid = MyName Here <(256) 428-6000>
language = en
overridecontext = no
mohinterpret = default
active = yes                 ; This option should only be set for one console.
                             ; It means that it is the active console to be
                             ; used from the Asterisk CLI.

Generated on Thu Apr 16 06:34:42 2015 for Asterisk - The Open Source Telephony Project by  doxygen 1.5.6